Skip to content
DoorsEZDoorsEZBook online
DoorsEZDoorsEZ

Symptom: won't open

Garage door won't open? Fix it safely in Orange County

Start with the checks that are safe: power, the wall control's lock, remote batteries, whether the opener is disconnected and the manual lock. If those pass, the cause is likely a spring or cable, and that part is our job.

Inside a two-car garage, a raised-panel steel door with vertical struts, gridded top windows, a torsion spring and ceiling opener
  • Open 24/7 ยท a person answers

    Same-day on most repairs booked by 11 am.

  • Callback within 15 minutes

    Day or night, every day.

  • Written price first

    Nothing starts until you approve it.

  • CSLB Lic. #859029

    C-61 / D-28 ยท Verify on the CSLB website (opens in a new tab)

The short answer

The short answer

A garage door that will not open usually has one of five causes: no power to the opener, a locked wall control, dead remote batteries, a disconnected opener trolley, or a broken spring or cable. Check the first four safely yourself. If a spring has a gap or a cable hangs loose, stop and call DoorsEZ at (833) 366-7739.

Safety first

If you see a gap in a spring, a loose or frayed cable, or the door feels too heavy to lift, stop. Do not keep pressing the remote; the opener will strain against a door the springs no longer support. Do not wind, adjust or remove springs or cables, which hold stored tension, and do not pull the emergency release on a partly open door with a broken spring.

What you might notice

  • Nothing happens when you press the remote or the wall button
  • The opener hums or clicks but the door does not move
  • The motor runs and the chain or belt moves, but the door stays put
  • The door rises a few inches, then stops or reverses
  • You heard a loud bang from the garage earlier
  • The door feels very heavy when you try to lift it by hand

What you get

What the work includes

  • Checking power, the wall control, remotes and opener settings
  • Inspecting springs, cables, drums and bottom brackets for breaks or slack
  • Checking track, rollers and the manual lock for anything binding the door
  • Opener diagnosis: motor, drive gear, trolley and control board
  • A written price for the fix, approved before work starts
  • Reverse test after any opener work (HSC section 19890)

How it works

From your call to a working door

  1. Run the safe checks

    Power, the wall control lock, the remote battery, the opener connection and the manual lock. Each is explained on this page, and none involves the springs.

  2. Look, do not touch

    From the floor, look for a gap in a spring or a slack or frayed cable. If you see one, unplug the opener and stop pressing the remote.

  3. Book or call

    Book online or call (833) 366-7739. The dispatcher confirms a time window. A photo of the springs and both bottom corners helps.

  4. Diagnose, price, fix

    The technician finds the cause, explains it and writes down the price. After you approve, we make the repair and test the door, including the reverse test after opener work (HSC section 19890).

Details

Five checks that are safe to do

Work through these in order. None of them puts you near a spring or cable.

  1. Power. Is the opener's light on? If not, check that it is plugged in, then check the breaker and any GFCI outlet in the garage, which can trip and cut power to the ceiling outlet.
  2. Wall control lock. Many wall controls have a lock or vacation button that turns off the remotes. If the wall button works but the remotes do not, look for it.
  3. Remote batteries. If the wall button works and the remote does not, replace the remote battery, then reprogram the remote from your opener manual if needed.
  4. Opener disconnected. If the motor runs and the chain or belt moves but the door stays put, the opener is disconnected from the door, usually because someone pulled the red release. With the door closed, reconnect it the way your manual describes.
  5. Manual lock. Some doors have a slide bar or a T-handle lock. If it is engaged, the opener cannot lift the door.

For example, a Fullerton homeowner presses the remote at 7 a.m. and nothing happens; the opener light is off. The breaker is fine, but a GFCI outlet on the garage wall has tripped. Pressing its reset button brings the opener back.

Signs the cause is a spring or cable

If the five checks pass, look up at the hardware from the floor. Do not climb a ladder next to it and do not touch it.

A torsion spring sits on a bar above the door. A visible gap in the coil means it broke. Extension springs run alongside the horizontal tracks; look for one that is stretched out, snapped or hanging.

Lift cables run up each side of the door from the bottom corners. A cable that hangs slack, is frayed or has come off its drum means the door is no longer supported evenly.

Other clues: a loud bang from the garage earlier, a door that rises a few inches and stops, or an opener that hums and strains. Openers are designed to stop or reverse when the load is heavier than expected, and a door with a broken spring is exactly that.

Any of these means a technician visit. Stop pressing the remote, unplug the opener and call (833) 366-7739, or read our broken spring page for what the repair involves.

During a power outage

Openers sold or installed in California since July 1, 2019 must have a battery backup function (Health and Safety Code section 19892). If yours is newer, the wall button may still work during an outage.

If your opener has no backup, you can open the door by hand, but only when the springs look whole. With the door fully closed, pull the red emergency release cord and lift from the bottom. A balanced door lifts with moderate effort. If it feels very heavy, lower it gently and stop: the springs are not doing their job. When power returns, reconnect the opener as your manual describes.

Any new residential opener we install has battery backup. Subdivision (c) of section 19892 also bars connecting a replacement door to an existing opener without one, so if you are planning a new door, plan on checking the opener at the same time. We service LiftMaster, Genie and Chamberlain openers.

Price

What affects the cost

The fix can be as small as a reset outlet or a reprogrammed remote, or as large as new springs, cables or an opener. Door size and weight, spring type and the opener model change the price. The technician writes it down after diagnosing the door, and nothing starts until you approve.

How our pricing works

Questions

Won't open questions

Still unsure? Call (833) 366-7739 and talk to a person.

Why does my opener run but the door does not move?

Usually the opener is disconnected from the door, often after someone pulled the red release. Less often, the opener's drive gear has stripped. If reconnecting with the door closed does not fix it, book an opener repair.

Can I open the door by hand?

Yes, if the springs are intact. With the door fully closed, pull the emergency release and lift. If the door feels very heavy, lower it gently and stop; a spring has likely failed.

My remote stopped working but the wall button works. What now?

Replace the remote battery and check the wall control's lock button. If it still fails, the remote may need reprogramming. We program remotes for LiftMaster, Genie and Chamberlain openers.

The door goes up a few inches, then stops. Why?

That pattern usually means the opener is meeting more weight than it expects, most often from a broken spring or cable. Stop pressing the remote, unplug the opener and call (833) 366-7739.

Do I need a new opener?

Not necessarily. Many no-open problems turn out to be power, remotes, springs or cables. The technician diagnoses first and gives you a written price for the repair, and prices a replacement only if the opener itself is the cause.

Open 24/7 ยท a person answers

Talk to a person today

Book online or call (833) 366-7739. We call back within 15 minutes, day or night.