Skip to content
DoorsEZDoorsEZBook online
DoorsEZDoorsEZ

Symptom: won't close

Garage door won't close? Get it shut in Orange County

Most doors that refuse to close are reacting to the photo eyes, the two safety sensors near the floor. Check those first, then the remote, power and track, and leave springs and cables to us.

White long-panel double garage door with a top row of windows sitting unevenly with a gap under one side, below a tile roof
  • Open 24/7 ยท a person answers

    Same-day on most repairs booked by 11 am.

  • Callback within 15 minutes

    Day or night, every day.

  • Written price first

    Nothing starts until you approve it.

  • CSLB Lic. #859029

    C-61 / D-28 ยท Verify on the CSLB website (opens in a new tab)

The short answer

The short answer

When a garage door will not close, or reverses before it reaches the floor, check the photo eyes first: something blocking the beam, a dirty lens, a bumped sensor or low sun shining into it. Then check remote batteries, the wall control lock and power. If the door is crooked or a spring is broken, call DoorsEZ at (833) 366-7739.

Safety first

Do not tape over, unplug or bypass the photo eyes to make the door close. They are what stops a closing door from striking a child, a pet or a car. Do not adjust springs or cables, which hold stored tension and can release suddenly. If you close the door by holding the wall button, watch it the whole way down and keep everyone clear.

What you might notice

  • The door starts down, then reverses back up
  • The door closes only while you hold the wall button down
  • The opener light flashes and the door will not move down
  • The door reverses just before or right at the floor
  • The remote does nothing, but the wall button works
  • The door tilts, binds or scrapes on the way down

What you get

What the work includes

  • Photo eye alignment, wiring and bracket check
  • Close limit and force settings adjusted to the door
  • Track, rollers and hinges checked for bends, binding and obstructions
  • Spring and cable inspection
  • Remotes and wall control checked, and reprogrammed if needed
  • Reverse test on a rigid two-inch obstacle after opener work (HSC section 19890)
  • A written price for any repair, approved before work starts

How it works

From your call to a working door

  1. Check the photo eyes

    Clear the beam, wipe both lenses, check that the indicator lights are steady and look for damaged wires.

  2. Check power and remotes

    Try the wall button, replace the remote battery, look for a lock setting on the wall control and check the breaker and any GFCI outlet.

  3. Book or call

    If the door still will not close, or it is crooked or binding, book online or call (833) 366-7739. The dispatcher confirms a time window.

  4. Diagnose, price, repair, test

    The technician finds the cause and writes down the price. After you approve, we make the repair and run the reverse test California requires after opener work (Health and Safety Code section 19890).

Details

Start with the photo eyes

The photo eyes are two small sensors mounted low on each side of the door, facing each other. One sends a beam; the other watches for it. If the beam is broken or the sensors cannot see each other, the opener will not close the door, or it will reverse it.

  1. Clear the beam. Look for a trash bin, broom, box, leaves or a spider web in the path.
  2. Clean the lenses. Wipe both with a soft, dry cloth.
  3. Check alignment. On many models each sensor has an indicator light, and one goes out or blinks when they are misaligned. Brackets get bumped by bikes and bins; nudge the sensor by hand until the light is steady.
  4. Check the wires. Look for a wire pulled loose, pinched or chewed along the wall.

Sun can also blind a sensor. In a west-facing garage, say in Huntington Beach on a winter afternoon, low sun can shine straight into the receiving eye, and the door will not close until the sun moves. We can swap the sensors so the receiver faces away from the sun, or shade it.

Remote, wall control and power

If the door will not move at all when you try to close it, work through the basics.

Try the wall button. If it works and the remote does not, replace the remote battery. If neither works and the opener light is off, check the plug, the breaker and any GFCI outlet in the garage. Then look for a lock or vacation setting on the wall control, which turns off the remotes.

During an outage, openers sold or installed in California since July 1, 2019 must have battery backup (Health and Safety Code section 19892), so a newer opener may still close the door. If yours has none, you can lower the door by hand only if it sits straight in its tracks and the springs look whole: pull the emergency release, lower the door with control, then engage the manual lock if the door has one. An opener left disconnected without a lock lets the door be lifted from outside.

On many openers, holding the wall button down until the door reaches the floor will close it even with a sensor fault. Watch it the whole way and keep everyone clear. It secures the house for the night; it does not fix the fault.

When the door reverses at the floor or binds on the way down

A door that comes almost all the way down and then goes back up is often running into its close limit or force setting. The close limit tells the opener where the floor is; if it is set too low, the opener reads the floor as an obstacle and reverses. Something on the floor, such as a raised mat or debris, or a bottom seal that has worn unevenly, can cause the same thing.

A door that tilts, scrapes or stops partway has a different problem: a bent track, a damaged roller or a cable losing tension on one side. The opener feels the extra resistance and reverses, which is the safety system doing its job. Running it again and again can pull the door off its track, so stop and call.

Limits and force are safety settings. We set them to your door, then run the reverse test that Health and Safety Code section 19890(e) requires of a technician who services or repairs an opener: the door must reverse when it meets a rigid two-inch obstacle. Track, roller and cable repairs get a written price first, and nothing starts until you approve.

Price

What affects the cost

A sensor realignment or a settings change needs few or no parts; new sensors, track sections, rollers, cables or an opener cost more. The door's size and the opener model also matter. The technician writes the price down after diagnosing the door, and nothing starts until you approve.

How our pricing works

Questions

Won't close questions

Still unsure? Call (833) 366-7739 and talk to a person.

Why does my garage door go down and then back up?

Usually the photo eyes see something in the beam or cannot see each other. If the door reverses right at the floor, the close limit or force setting needs adjusting, and those are safety settings best left to a technician.

Why does the door only close if I hold the button down?

On many openers, holding the wall button overrides a photo-eye fault. It means the sensors need attention: clear, clean and align them and check the wiring, then book a visit if the fault stays.

Can I unplug or bypass the safety sensors?

No. They stop a closing door from striking a person, a pet or a car, and we will not bypass them. If they keep faulting, we repair or replace them.

Why does it fail only in the late afternoon?

Low sun shining into a photo eye can blind it. If the problem comes and goes with the time of day, that is the likely cause, and we can reposition or shade the sensors.

Is a door that will not close an emergency?

It can be if it leaves the house open overnight. Lock the door between the garage and the house, follow the steps on our emergency page and call (833) 366-7739.

Open 24/7 ยท a person answers

Talk to a person today

Book online or call (833) 366-7739. We call back within 15 minutes, day or night.